Feeds:
Posts
Comments

Posts Tagged ‘Nankeen Brown cotton’

OLYMPUS DIGITAL CAMERAI have completed another garment with my homegrown cotton! You may recall that I made a vest from my homegrown, handspun, handwoven, naturally-colored cotton in 2015. For the vest I used my green cotton. I had grown green and brown in separate gardens, but they crossed. There was some brown and a bit of white (although I wasn’t growing any white) mixed in with the green and I spun it all together. It was easier that way since I was spinning it off the seed.

book-charkha-cotton-seeds-mat-blog

Indian book charkha

This time I carefully separated out the colors and took the seeds out by hand before spinning. Examining the seed and noticing the feel of the fiber helped with identification, since sometimes the colors are so faint at harvest that it is hard to tell them apart. Once the fiber is spun and boiled to set the twist, the color pops. As for feel, the green feels a bit silky compared to the brown. The green fiber is also a little longer than the brown. The Nankeen brown seed I was working with is naked seed with no lint on it. Everything else had fuzzy seeds. I spun all the cotton for the shirt on my Indian book charkha that I bought from Eileen Hallman at New World Textiles.  I plied the singles on my Louet10 wheel. I had Nankeen Brown, Erlene’s Green, and light brown. When I got right down to it, I didn’t have enough green and brown fiber for my project, so I used the white cotton I had grown in the late 1990s. I didn’t know how to spin then and had put it away in a box, seeds and all. That first homegrown cotton is now in my new shirt.

loom-with-fabric-for-shirt-blog

My loom with fabric for the shirt on it.

I spun the brown, green, and white separately, then plied brown and green together and brown and white together. I used the same 12″ table loom as I used for my vest, resulting in 9½” wide panels of fabric to work with. There are 2 panels on each front and back and ½ panel on each side. Each sleeve is made from 2½ panels. I wanted to conserve as much of the fabric as I could, cutting only the lengths apart. The only shaping was for the neck. The color of the cotton that had crossed expressed itself as light brown, whether it was in the brown bed or the green bed. I used the light brown for my warp. My loom has 8 spaces per inch on the beater bar and enough string heddles for 8 ends per inch (epi). I could have made more heddles and doubled up the warp ends through the beater bar, but I didn’t. The 8 epi made for a weft faced fabric like my vest. I used my homegrown 2-ply cotton throughout.

OLYMPUS DIGITAL CAMERAI wove four full length (30½”) panels for the front and back. The change of color from brown/white to brown/green is woven in, not pieced. The side panel was woven at 22” long. The sleeve panels were woven at 14” (10½” brown/white ply and 3½” brown/green). The hem is 1” plus an additional ⅜” turned in from there. I had to make sure to allow for shrinkage when I determined my measurements for weaving. Shrinkage in the length amounted to about 8%.

Most of the seams were ¼”. I made facing for the neckline from cotton fabric that had been dyed with black walnuts. There is a ⅜” seam at the shoulders. I designed this pattern myself and made a shirt from pieces of denim saved from old jeans to try it out before cutting my homegrown cotton. The shirt fit beautifully. To make more room in my hips, especially when putting my hands in my pockets, I did not bring the seams where the front and back panels connect to the side panels down all the way to the hem, leaving a few inches open. Those edges were faced with the walnut dyed cotton.

yarn-for-shirt-blog

Cotton used in my shirt. I didn’t need the green/white ball.

The hardest part of this project was estimating how much fiber I needed. I had the calculations of how much 2-ply yarn it took to make my vest, but now I was using a charkha to spin. That, combined with having more spinning experience, my yarn was finer, requiring more yards per woven inch. I needed to calculate carefully because I had a limited amount of fiber. By keeping careful records and weaving a sample, I estimated that I needed 43.65 yards of raw singles for each 1” of weaving. This cotton would get boiled twice—once after spinning into singles and again after plying. I estimated about 12.5% total shrinkage for that. Once everything was plied, I needed a figure for how much 2-ply yarn necessary to finish my project. I estimated 22.2 yards of 2-ply yarn for each inch of weaving. My calculations from actual weaving were 18.1-22.2 yards of 2-ply for each inch of weaving. Thinking back to the 43.65 yards of raw singles, taking out 12.5% for shrinkage and dividing it by 2 to make the 2-ply yarn, I would end up with 19 yards of 2-ply per inch of weaving. There are many ways to calculate and I wanted to use generous estimates to make sure I had enough fiber. Periodically I checked my 2-ply yarn for wraps per inch (wpi) and found it to vary from 29-35 wpi.

I loved doing this project, although, at times I thought I would go crazy doing the calculations. I wanted something appropriate to wear it with, so I made a pair of jeans from naturally brown denim I bought from Sally Fox at Vreseis.com. I’m wearing those jeans in the top photo.

I am enjoying wearing this shirt everywhere I can. It is so comfortable! The design allows freedom of movement and that contributes to the comfort, but I think all the good energy it embodies contributes even more. Knowing I grew it from saved seeds, spun, wove, and sewed it gives me a great feeling of satisfaction. I want to encourage other spinners out there to do the same. This shirt weighs 14 ounces. To give you an idea of how much space you would need to grow that much, in my Grow and Spin Cotton post I gave yields of 12-16 ounces per 100 sq. ft. Your yield could be higher or lower, depending on where you live. I hope you give it a try!homeplace earth

Read Full Post »

Cindy in her homegrown, handspun cotton vest.

Cindy in her homegrown, handspun cotton vest.

My new vest is finished! In the photo I am wearing my new homegrown, handspun, handwoven, naturally-colored cotton vest. It has been a long time in coming. Growing the cotton and sewing the vest are skills and knowledge I already had. The spinning and weaving were things I needed to learn.

Homegrown cotton and takli spindle.

Homegrown cotton and takli spindle.

In February 2013 I wrote of my cotton spinning journey in my blog post Grow and Spin Cotton. I’ll repeat the photo here of my Nankeen Brown cotton, Erlene’s Green cotton, and takli spindle. All the fiber for the vest was spun on that spindle. Since cotton has such a short fiber length, it is helpful to use a support spindle, which is what a takli is. A small bowl supports the bottom of the spindle while it spins. Once the cotton was spun into singles I plied two singles into 2-ply yarn, which is what I used to weave with. The plying was done on a drop spindle that I made from a dowel and a small wooden wheel.

Small table loom with fabric for homegrown, handspun cotton vest.

Small table loom with fabric for homegrown, handspun cotton vest.

Joining Clothos Handspinners has been an important part of this fiber adventure. I learn so much from attending the meetings and interacting with the members. Every two years the group holds a swap meet which is an opportunity for members to sell extra equipment, fiber, and books and for others (like me) to acquire it. Some of that trading also goes on informally at the regular meetings. The swap meet was where I bought my loom. Then I had to learn to use it. This vest has not been an easy project. The loom is 12” wide, but my resulting fabric was only 9½” wide. I made a pattern from the quilted vest I wear, and from that, designed a pattern that used 9½” wide fabric. Since 9½” is not wide enough for a full front or back panel, there are side panels that make up the difference.

Erlene's green and Nankeen brown cotton spun and woven.

Erlene’s green and Nankeen brown cotton spun and woven.

I used brown for the warp and green for the weft. As you can see, the weft is dominant in the weaving. I grew both colors in the garden and, although they were a good distance apart, there was some crossing. I didn’t notice green in with the brown, but there would be some brown in with the green. Maybe brown is the dominant color when it comes to genetics. When I was spinning I didn’t separate the off-color fibers, so there was some brown spun with the green, just as it was harvested. The fiber from the green cotton plants also had bits of white. It made for a pleasant variation in color in the finished fabric. Although I did do some carding, mostly I spun the fiber right off the seed.

As noted in my 2013 blog post, my 2012 yield (fiber only, no seeds) was .75 lb (green) to 1 lb. (brown) fiber per 100 sq. ft. The weight of my vest is 11.5 oz. (.72 lb.) including lining and buttons. Frequently people assume I would have had to grow cotton on a larger scale to produce an item of clothing, but this can be done in a garden. I used cotton osnaburg fabric for the lining—a piece I had left from a previous project. Osnaburg has an earthy appearance and seemed right for the vest. Besides, I already had it.

Button made from a shell on the homegrown, handspun cotton vest.

Button made from a shell on the homegrown, handspun cotton vest.

Although I usually don’t button my vests closed, I wanted to have buttons and I wanted them to be special. My first thought was to make wooden buttons, but then I remembered the jar of shells our children picked up at the beach many years ago. I used small vice grips to nip the edges of a shell off—going round and round until it was the size I wanted for a button. Then I drilled two ⅟₁₆” holes in each button. I didn’t want to put buttonholes in my new fabric so I made loops by braiding my brown cotton yarn to close the vest, if I should want to. This was my first time making buttons from shells and I am pleased with the results. In the photo you can see a bit of the osnaburg lining.

Now that I know how to spin and weave, the possibilities for unique yarns and fabrics are endless. I will be learning about natural dyes and eventually learn to spin wool and to use a wheel. When I was at the Mother Earth News Fair in Asheville, NC in April I bought a book charka from Eileen Hallman at New World Textiles, but I haven’t used it yet so as not to distract me from finishing the vest. Once I learn how to use it, the charka will speed up my cotton spinning. For this vest I wanted to use the least technology that I could, not only because it was the least expensive way to go (which was a consideration), but because I wanted to relate to how people down through the ages worked with fiber to clothe themselves. I’m sure in some places people still depend on these methods and, you can be sure, I kept them in my heart while I worked.

When I first grew cotton I had no idea what to do with it and put it away in a box for at least ten years. It has taken some effort to learn to spin and to get to the point of making a vest with my homegrown cotton. I might have finished the vest earlier if I wasn’t sidetracked writing two books during that time. You might not be into growing and spinning your own cotton, but there is probably some other adventure that has been rolling around in your head for awhile—maybe even ten years or more. I want to encourage you to go for it. If I can learn to do this, you can learn new tricks, too.

I’ll be wearing my new vest at upcoming events this year, which are listed here. First up is the Slow Living Summit in Brattleboro, Vermont on June 3-5. See you there!

Read Full Post »

%d bloggers like this: